Mangler hjælp til nyt usb trådløs

[wappa]

Hej
Jeg har fået en ny trådløs usb af mærke Deltaco og det er driver med til linux på cd`en men hvordan få jeg skidtet indstalleret.

Det er en READ ME fil men fatter minus af det ..hjælp det er hvad det står i filen håber i kan se hvad jeg skal gøre.

læs her:


Release Date: 2006-02-09, ver 1.2

RTL8187 Linux driver version 1.2



--This driver supports RealTek RTL8187 Wireless LAN driver for

Fedora Core 2/3/4/5, Debian 3.1, Mandrake 10.2/Mandriva 2006,

SUSE 9.3/10.1/10.2, Gentoo 3.1, etc.

- Support Client mode for either infrastructure or adhoc mode

- Support WEP and WPAPSK connection



< Component >

The driver is composed of several parts:

1. Module source code

stack.tar.gz

drv.tar.gz



2. Script ot build the modules

makedrv



3. Script to load/unload modules

wlan0up

wlan0down



4. Script and configuration for DHCP

wlan0dhcp

ifcfg-wlan0

4. Supplicant source code:

wpa_supplicant-0.4.9.tar.gz



5. Example of supplicant configuration file:

wpa1.conf



< Installation >

Runing the scripts can finish all operations of building up modules

from the source code and start the nic.

1. Build up the drivers from the source code

./makedrv



2. load the driver module to kernel and start up nic

./wlan0up



< Set wireless lan MIBs >

This driver uses Wireless Extension as an interface allowing you to set

Wireless LAN specific parameters.



Current driver supports "iwlist" to show the device status of nic

iwlist wlan0 [parameters]

where

parameter explaination [parameters]

----------------------- -------------

Show available chan and freq freq / channel

Show and Scan BSS and IBSS scan[ning]

Show supported bit-rate rate / bit[rate]

Show Power Management mode power



For example:

iwlist wlan0 channel

iwlist wlan0 scan

iwlist wlan0 rate

iwlist wlan0 power



Driver also supports "iwconfig", manipulate driver private ioctls, to set

MIBs.



iwconfig wlan0 [parameters] [val]

where

parameter explaination [parameters] [val] constraints

----------------------- ------------- ------------------

Connect to AP by address ap [mac_addr]

Set the essid, join (I)BSS essid [essid]

Set operation mode mode {Managed|Ad-hoc}

Set keys and security mode key/enc[ryption] {N|open|restricted|off}



For example:

iwconfig wlan0 ap XX:XX:XX:XX:XX:XX

iwconfig wlan0 essid "ap_name"

iwconfig wlan0 mode Ad-hoc

iwconfig wlan0 mode essid "name" mode Ad-hoc

iwconfig wlan0 key 0123456789 [2] open

iwconfig wlan0 key off

iwconfig wlan0 key restricted [3] 0123456789



< Getting IP address >

After start up the nic, the network needs to obtain an IP address before

transmit/receive data.

This can be done by setting the static IP via "ifconfig wlan0 IP_ADDRESS"

command, or using DHCP.



If using DHCP, setting steps is as below:

(1)connect to an AP via "iwconfig" settings

iwconfig wlan0 essid [name] or

iwconfig wlan0 ap XX:XX:XX:XX:XX:XX



(2)run the script which run the dhclient

./wlan0dhcp

or

dhcpcd wlan0

(Some network admins require that you use the

hostname and domainname provided by the DHCP server.

In that case, use

dhcpcd -HD wlan0)



< WPAPSK >

WPA_SUPPLICANT help the network to communicate under the protection of WPAPSK

mechanism



(1)Unpack source code of WPA supplicant:

tar -zxvf wpa_supplicant-0.4.9.tar.gz

cd wpa_supplicant-0.4.9



(2)Create .config file:

cp defconfig .config



(3)Edit .config file, uncomment the following line:

#CONFIG_DRIVER_IPW=y.



(4)Build WPA supplicant:

make

If make error for lack of <include/md5.h>, install the openssl lib(two ways):

1. Install the openssl lib from corresponding installation disc:

Fedora Core 2/3/4/5(openssl-0.9.71x-xx), Mandrake10.2/Mandriva10.2(openssl-0.9.7x-xmdk),

Debian 3.1(libssl-dev), Suse 9.3/10.0/10.1(openssl_devl), Gentoo(dev-libs/openssl), etc.

2. Download the openssl open source package from www.openssl.org, build and install it.



(5)Edit wpa_supplicant.conf to set up SSID and its passphrase.

For example, the following setting in "wpa1.conf" means SSID

to join is "BufAG54_Ch6" and its passphrase is "87654321".

network={

ssid="BufAG54_Ch6"

proto=WPA

key_mgmt=WPA-PSK

pairwise=CCMP TKIP

group=CCMP TKIP WEP104 WEP40

psk="87654321"

priority=2

}



(6)Execute WPA supplicant (Assume 8187 and related modules had been

loaded):

./wpa_supplicant -D ipw -c wpa1.conf -i wlan0 &

[Stra]

Har du prøvet bare at putte den i USB stik og aktivere trådløs netværksunderstøttelse ved at højreklikke på netværksikonet?

Stra

[wappa]

ja det har jeg og signalet meget dårlig faktisk kun èn streg og trådløse router står ca 3 meter fra mig, og tænkte så på om hvis nu man indstallerede driver som fulgte med om det har nogen betydning

[Stra]

ja det har jeg og signalet meget dårlig faktisk kun èn streg og trådløse router står ca 3 meter fra mig, og tænkte så på om hvis nu man indstallerede driver som fulgte med om det har nogen betydning

Ville jeg tvivle på? men prøv at komme med output på

Kode: Vælg alt

iwconfig

Stra

[Warhawk]

Du skal ikke bruge den medfølgende driver, da der er indbygget driver i Ubuntu 8.10, og denne er sidst nye.

[wappa]

ok tak