Det er lidt svært at se hvad den skriver når den starter op, men når den ikke montere de to dreve, så kan jeg lige nå at se noget med Fail og ntfs-3g. Så vidt jeg kan se står der ikke noget i outputtet fra dmesg:
Kode: Vælg alt
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-27) (maks@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sat Oct 30 22:47:19 UTC 2010
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000afef0000 (usable)
[ 0.000000] BIOS-e820: 00000000afef0000 - 00000000afef3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000afef3000 - 00000000aff00000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000b0000000 - 00000000c0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000250000000 (usable)
[ 0.000000] DMI 2.4 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xafef0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FE0000000 write-back
[ 0.000000] 2 base 0A0000000 mask FF0000000 write-back
[ 0.000000] 3 base 100000000 mask F00000000 write-back
[ 0.000000] 4 base 200000000 mask FC0000000 write-back
[ 0.000000] 5 base 240000000 mask FF0000000 write-back
[ 0.000000] 6 base 0AFF00000 mask FFFF00000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000aff00000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000373fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037000000 page 2M
[ 0.000000] 0037000000 - 00373fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 373fe000 @ 10000-16000
[ 0.000000] RAMDISK: 37e23000 - 37fef867
[ 0.000000] Allocated new RAMDISK: 00100000 - 002cc867
[ 0.000000] Move RAMDISK from 0000000037e23000 - 0000000037fef866 to 00100000 - 002cc866
[ 0.000000] ACPI: RSDP 000f7de0 00024 (v02 Nvidia)
[ 0.000000] ACPI: XSDT afef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP afefb7c0 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT afef3240 0850B (v01 NVIDIA AWRDACPI 00001000 MSFT 03000000)
[ 0.000000] ACPI: FACS afef0000 00040
[ 0.000000] ACPI: HPET afefba00 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
[ 0.000000] ACPI: MCFG afefba80 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: APIC afefb900 00098 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: SSDT afefbb00 0087B (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1930MB HIGHMEM available.
[ 0.000000] 883MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 373fe000
[ 0.000000] low ram: 0 - 373fe000
[ 0.000000] node 0 low ram: 00000000 - 373fe000
[ 0.000000] node 0 bootmap 00012000 - 00018e80
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 00014c7bb4] TEXT DATA BSS ==> [0001000000 - 00014c7bb4]
[ 0.000000] #4 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
[ 0.000000] #5 [00014c8000 - 00014ce159] BRK ==> [00014c8000 - 00014ce159]
[ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] #7 [0000100000 - 00002cc867] NEW RAMDISK ==> [0000100000 - 00002cc867]
[ 0.000000] #8 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000]
[ 0.000000] found SMP MP-table at [c00f6290] f6290
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000373fe
[ 0.000000] HighMem 0x000373fe -> 0x000afef0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000afef0
[ 0.000000] On node 0 totalpages: 720511
[ 0.000000] free_area_init_node: node 0, pgdat c13b2720, node_mem_map c14d0200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1736 pages used for memmap
[ 0.000000] Normal zone: 220470 pages, LIFO batch:31
[ 0.000000] HighMem zone: 3862 pages used for memmap
[ 0.000000] HighMem zone: 490460 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfeff0000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:30000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c2c00000 s34296 r0 d23048 u1048576
[ 0.000000] pcpu-alloc: s34296 r0 d23048 u1048576 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 714881
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=add37ff5-8d1f-47da-a429-61c57cf9c3d3 ro vga=792 GRUB_CMDLINE_LINUX=
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000373fe:000afef0)
[ 0.000000] Memory: 2850528k/2882496k available (2499k kernel code, 30384k reserved, 1324k data, 372k init, 1977288k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.000000] .init : 0xc13bd000 - 0xc141a000 ( 372 kB)
[ 0.000000] .data : 0xc1270fd9 - 0xc13bc320 (1324 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1270fd9 (2499 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3000.186 MHz processor.
[ 0.004004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6000.37 BogoMIPS (lpj=12000744)
[ 0.004016] Security Framework initialized
[ 0.004021] SELinux: Disabled at boot.
[ 0.004027] Mount-cache hash table entries: 512
[ 0.004113] Initializing cgroup subsys ns
[ 0.004116] Initializing cgroup subsys cpuacct
[ 0.004120] Initializing cgroup subsys devices
[ 0.004122] Initializing cgroup subsys freezer
[ 0.004124] Initializing cgroup subsys net_cls
[ 0.004141] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004144] CPU: L2 cache: 6144K
[ 0.004146] CPU: Physical Processor ID: 0
[ 0.004148] CPU: Processor Core ID: 0
[ 0.004151] mce: CPU supports 6 MCE banks
[ 0.004157] CPU0: Thermal monitoring enabled (TM1)
[ 0.004161] using mwait in idle threads.
[ 0.004166] Performance Events: Core2 events, Intel PMU driver.
[ 0.004171] ... version: 2
[ 0.004173] ... bit width: 40
[ 0.004175] ... generic registers: 2
[ 0.004177] ... value mask: 000000ffffffffff
[ 0.004179] ... max period: 000000007fffffff
[ 0.004181] ... fixed-purpose events: 3
[ 0.004183] ... event mask: 0000000700000003
[ 0.004187] Checking 'hlt' instruction... OK.
[ 0.020807] ACPI: Core revision 20090903
[ 0.028055] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.028469] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.070760] CPU0: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
[ 0.072001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.008000] CPU: L2 cache: 6144K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU1: Thermal monitoring enabled (TM1)
[ 0.156019] CPU1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
[ 0.156034] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.160030] Brought up 2 CPUs
[ 0.160033] Total of 2 processors activated (12000.31 BogoMIPS).
[ 0.160744] CPU0 attaching sched-domain:
[ 0.160747] domain 0: span 0-1 level MC
[ 0.160749] groups: 0 1
[ 0.160752] CPU1 attaching sched-domain:
[ 0.160753] domain 0: span 0-1 level MC
[ 0.160755] groups: 1 0
[ 0.160794] devtmpfs: initialized
[ 0.160794] regulator: core version 0.5
[ 0.160794] NET: Registered protocol family 16
[ 0.160794] ACPI: bus type pci registered
[ 0.160794] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 31
[ 0.160794] PCI: MCFG area at f0000000 reserved in E820
[ 0.160794] PCI: Using MMCONFIG for extended config space
[ 0.160794] PCI: Using configuration type 1 for base access
[ 0.160794] mtrr: your CPUs had inconsistent fixed MTRR settings
[ 0.160794] mtrr: probably your BIOS does not setup all CPUs.
[ 0.160794] mtrr: corrected configuration.
[ 0.160794] bio: create slab <bio-0> at 0
[ 0.160794] ACPI: EC: Look up EC in DSDT
[ 0.168549] ACPI: Interpreter enabled
[ 0.168557] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.168577] ACPI: Using IOAPIC for interrupt routing
[ 0.175290] ACPI: No dock devices found.
[ 0.175352] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.176067] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.176071] pci 0000:00:03.0: PME# disabled
[ 0.176285] pci 0000:00:0a.1: reg 10 io port: [0xff00-0xff3f]
[ 0.176299] pci 0000:00:0a.1: reg 20 io port: [0x1c00-0x1c3f]
[ 0.176303] pci 0000:00:0a.1: reg 24 io port: [0x1c80-0x1cbf]
[ 0.176325] pci 0000:00:0a.1: PME# supported from D3hot D3cold
[ 0.176331] pci 0000:00:0a.1: PME# disabled
[ 0.176360] pci 0000:00:0b.0: reg 10 32bit mmio: [0xeffff000-0xefffffff]
[ 0.176385] pci 0000:00:0b.0: supports D1 D2
[ 0.176387] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.176391] pci 0000:00:0b.0: PME# disabled
[ 0.176414] pci 0000:00:0b.1: reg 10 32bit mmio: [0xefffe000-0xefffe0ff]
[ 0.176441] pci 0000:00:0b.1: supports D1 D2
[ 0.176442] pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.176446] pci 0000:00:0b.1: PME# disabled
[ 0.176481] pci 0000:00:0d.0: reg 20 io port: [0xfc00-0xfc0f]
[ 0.176517] pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
[ 0.176520] pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
[ 0.176524] pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
[ 0.176528] pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
[ 0.176531] pci 0000:00:0e.0: reg 20 io port: [0xf700-0xf70f]
[ 0.176535] pci 0000:00:0e.0: reg 24 32bit mmio: [0xefffd000-0xefffdfff]
[ 0.176576] pci 0000:00:0e.1: reg 10 io port: [0x9e0-0x9e7]
[ 0.176579] pci 0000:00:0e.1: reg 14 io port: [0xbe0-0xbe3]
[ 0.176583] pci 0000:00:0e.1: reg 18 io port: [0x960-0x967]
[ 0.176587] pci 0000:00:0e.1: reg 1c io port: [0xb60-0xb63]
[ 0.176590] pci 0000:00:0e.1: reg 20 io port: [0xf200-0xf20f]
[ 0.176594] pci 0000:00:0e.1: reg 24 32bit mmio: [0xefffc000-0xefffcfff]
[ 0.176635] pci 0000:00:0e.2: reg 10 io port: [0xf100-0xf107]
[ 0.176638] pci 0000:00:0e.2: reg 14 io port: [0xf000-0xf003]
[ 0.176642] pci 0000:00:0e.2: reg 18 io port: [0xef00-0xef07]
[ 0.176646] pci 0000:00:0e.2: reg 1c io port: [0xee00-0xee03]
[ 0.176650] pci 0000:00:0e.2: reg 20 io port: [0xed00-0xed0f]
[ 0.176653] pci 0000:00:0e.2: reg 24 32bit mmio: [0xefffb000-0xefffbfff]
[ 0.176734] pci 0000:00:0f.1: reg 10 32bit mmio: [0xefff0000-0xefff3fff]
[ 0.176764] pci 0000:00:0f.1: PME# supported from D3hot D3cold
[ 0.176768] pci 0000:00:0f.1: PME# disabled
[ 0.176818] pci 0000:00:11.0: reg 10 32bit mmio: [0xefffa000-0xefffafff]
[ 0.176822] pci 0000:00:11.0: reg 14 io port: [0xec00-0xec07]
[ 0.176826] pci 0000:00:11.0: reg 18 32bit mmio: [0xefff9000-0xefff90ff]
[ 0.176830] pci 0000:00:11.0: reg 1c 32bit mmio: [0xefff8000-0xefff800f]
[ 0.176856] pci 0000:00:11.0: supports D1 D2
[ 0.176858] pci 0000:00:11.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.176863] pci 0000:00:11.0: PME# disabled
[ 0.176907] pci 0000:00:12.0: reg 10 32bit mmio: [0xefff7000-0xefff7fff]
[ 0.176911] pci 0000:00:12.0: reg 14 io port: [0xeb00-0xeb07]
[ 0.176915] pci 0000:00:12.0: reg 18 32bit mmio: [0xefff6000-0xefff60ff]
[ 0.176919] pci 0000:00:12.0: reg 1c 32bit mmio: [0xefff5000-0xefff500f]
[ 0.176945] pci 0000:00:12.0: supports D1 D2
[ 0.176946] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.176951] pci 0000:00:12.0: PME# disabled
[ 0.177002] pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.177005] pci 0000:00:13.0: PME# disabled
[ 0.177057] pci 0000:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.177061] pci 0000:00:16.0: PME# disabled
[ 0.177111] pci 0000:00:18.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.177115] pci 0000:00:18.0: PME# disabled
[ 0.177152] pci 0000:01:00.0: reg 10 32bit mmio: [0xec000000-0xecffffff]
[ 0.177159] pci 0000:01:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.177166] pci 0000:01:00.0: reg 1c 64bit mmio: [0xea000000-0xebffffff]
[ 0.177171] pci 0000:01:00.0: reg 24 io port: [0xdc00-0xdc7f]
[ 0.177175] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xedfe0000-0xedffffff]
[ 0.184056] pci 0000:00:03.0: bridge io port: [0xd000-0xdfff]
[ 0.184058] pci 0000:00:03.0: bridge 32bit mmio: [0xea000000-0xedffffff]
[ 0.184061] pci 0000:00:03.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.184095] pci 0000:02:0b.0: reg 10 32bit mmio: [0xefdff000-0xefdff7ff]
[ 0.184100] pci 0000:02:0b.0: reg 14 io port: [0xcc00-0xcc7f]
[ 0.184132] pci 0000:02:0b.0: supports D2
[ 0.184133] pci 0000:02:0b.0: PME# supported from D2 D3hot D3cold
[ 0.184137] pci 0000:02:0b.0: PME# disabled
[ 0.184164] pci 0000:00:0f.0: transparent bridge
[ 0.184168] pci 0000:00:0f.0: bridge io port: [0xc000-0xcfff]
[ 0.184170] pci 0000:00:0f.0: bridge 32bit mmio: [0xefd00000-0xefdfffff]
[ 0.184173] pci 0000:00:0f.0: bridge 32bit mmio pref: [0xefe00000-0xefefffff]
[ 0.184208] pci 0000:00:13.0: bridge io port: [0xb000-0xbfff]
[ 0.184210] pci 0000:00:13.0: bridge 32bit mmio: [0xefc00000-0xefcfffff]
[ 0.184214] pci 0000:00:13.0: bridge 64bit mmio pref: [0xefb00000-0xefbfffff]
[ 0.184261] pci 0000:04:00.0: reg 10 64bit mmio: [0xefaff000-0xefaff07f]
[ 0.184274] pci 0000:04:00.0: reg 18 64bit mmio: [0xefaf8000-0xefafbfff]
[ 0.184281] pci 0000:04:00.0: reg 20 io port: [0xac00-0xac7f]
[ 0.184294] pci 0000:04:00.0: reg 30 32bit mmio pref: [0xefa00000-0xefa7ffff]
[ 0.184327] pci 0000:04:00.0: supports D1 D2
[ 0.184354] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.184419] pci 0000:00:16.0: bridge io port: [0xa000-0xafff]
[ 0.184421] pci 0000:00:16.0: bridge 32bit mmio: [0xefa00000-0xefafffff]
[ 0.184424] pci 0000:00:16.0: bridge 64bit mmio pref: [0xef900000-0xef9fffff]
[ 0.184449] pci 0000:05:00.0: reg 10 32bit mmio: [0xe8000000-0xe8ffffff]
[ 0.184457] pci 0000:05:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
[ 0.184465] pci 0000:05:00.0: reg 1c 64bit mmio: [0xe6000000-0xe7ffffff]
[ 0.184470] pci 0000:05:00.0: reg 24 io port: [0x9c00-0x9c7f]
[ 0.184475] pci 0000:05:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.192059] pci 0000:00:18.0: bridge io port: [0x9000-0x9fff]
[ 0.192061] pci 0000:00:18.0: bridge 32bit mmio: [0xe6000000-0xe9ffffff]
[ 0.192065] pci 0000:00:18.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
[ 0.192076] pci_bus 0000:00: on NUMA node 0
[ 0.192080] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.192406] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.256902] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.257019] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.257134] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.257251] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 *11 14 15)
[ 0.257366] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 *11 14 15)
[ 0.257480] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.257596] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 *7 9 10 11 14 15)
[ 0.257709] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.257824] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.257939] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.258054] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 *7 9 10 11 14 15)
[ 0.258175] ACPI: PCI Interrupt Link [LMC1] (IRQs *5 7 9 10 11 14 15)
[ 0.258290] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[ 0.258403] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.258518] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.258633] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.258748] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.258864] ACPI: PCI Interrupt Link [LSID] (IRQs *5 7 9 10 11 14 15)
[ 0.258983] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
[ 0.259102] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)
[ 0.259244] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 0.259379] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 0.259515] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 0.259649] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
[ 0.259783] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
[ 0.259916] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
[ 0.260057] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0
[ 0.260190] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[ 0.260327] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
[ 0.260463] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[ 0.260597] ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0
[ 0.260732] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[ 0.260867] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
[ 0.261002] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
[ 0.261137] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
[ 0.261272] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[ 0.261407] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 0.261543] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[ 0.261678] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[ 0.261812] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0
[ 0.261898] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.261904] vgaarb: device added: PCI:0000:05:00.0,decodes=io+mem,owns=none,locks=none
[ 0.261908] vgaarb: loaded
[ 0.261918] PCI: Using ACPI for IRQ routing
[ 0.261918] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[ 0.261918] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 0.268016] Switching to clocksource tsc
[ 0.268825] pnp: PnP ACPI init
[ 0.268831] ACPI: bus type pnp registered
[ 0.271345] pnp: PnP ACPI: found 13 devices
[ 0.271347] ACPI: ACPI bus type pnp unregistered
[ 0.271351] PnPBIOS: Disabled by ACPI PNP
[ 0.271357] system 00:01: ioport range 0x1000-0x107f has been reserved
[ 0.271361] system 00:01: ioport range 0x1080-0x10ff has been reserved
[ 0.271364] system 00:01: ioport range 0x1400-0x147f has been reserved
[ 0.271367] system 00:01: ioport range 0x1480-0x14ff has been reserved
[ 0.271370] system 00:01: ioport range 0x1800-0x187f has been reserved
[ 0.271373] system 00:01: ioport range 0x1880-0x18ff has been reserved
[ 0.271377] system 00:01: iomem range 0xb0000000-0xbfffffff has been reserved
[ 0.271382] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.271385] system 00:02: ioport range 0x800-0x87f has been reserved
[ 0.271388] system 00:02: ioport range 0x290-0x297 has been reserved
[ 0.271391] system 00:02: ioport range 0x880-0x88f has been reserved
[ 0.271398] system 00:0b: iomem range 0xf0000000-0xf1ffffff has been reserved
[ 0.271403] system 00:0c: iomem range 0xf0000-0xf3fff could not be reserved
[ 0.271406] system 00:0c: iomem range 0xf4000-0xf7fff could not be reserved
[ 0.271409] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.271412] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
[ 0.271415] system 00:0c: iomem range 0xfeff0000-0xfeff00ff has been reserved
[ 0.271419] system 00:0c: iomem range 0xafef0000-0xafefffff could not be reserved
[ 0.271422] system 00:0c: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.271426] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.271429] system 00:0c: iomem range 0x100000-0xafeeffff could not be reserved
[ 0.271433] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.271436] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.271440] system 00:0c: iomem range 0xfeff0000-0xfeff03ff could not be reserved
[ 0.306088] pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
[ 0.306092] pci 0000:00:03.0: IO window: 0xd000-0xdfff
[ 0.306095] pci 0000:00:03.0: MEM window: 0xea000000-0xedffffff
[ 0.306099] pci 0000:00:03.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.306104] pci 0000:00:0f.0: PCI bridge, secondary bus 0000:02
[ 0.306107] pci 0000:00:0f.0: IO window: 0xc000-0xcfff
[ 0.306111] pci 0000:00:0f.0: MEM window: 0xefd00000-0xefdfffff
[ 0.306115] pci 0000:00:0f.0: PREFETCH window: 0xefe00000-0xefefffff
[ 0.306119] pci 0000:00:13.0: PCI bridge, secondary bus 0000:03
[ 0.306122] pci 0000:00:13.0: IO window: 0xb000-0xbfff
[ 0.306126] pci 0000:00:13.0: MEM window: 0xefc00000-0xefcfffff
[ 0.306130] pci 0000:00:13.0: PREFETCH window: 0x000000efb00000-0x000000efbfffff
[ 0.306135] pci 0000:00:16.0: PCI bridge, secondary bus 0000:04
[ 0.306138] pci 0000:00:16.0: IO window: 0xa000-0xafff
[ 0.306142] pci 0000:00:16.0: MEM window: 0xefa00000-0xefafffff
[ 0.306146] pci 0000:00:16.0: PREFETCH window: 0x000000ef900000-0x000000ef9fffff
[ 0.306152] pci 0000:00:18.0: PCI bridge, secondary bus 0000:05
[ 0.306155] pci 0000:00:18.0: IO window: 0x9000-0x9fff
[ 0.306159] pci 0000:00:18.0: MEM window: 0xe6000000-0xe9ffffff
[ 0.306163] pci 0000:00:18.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
[ 0.306172] pci 0000:00:03.0: setting latency timer to 64
[ 0.306176] pci 0000:00:0f.0: setting latency timer to 64
[ 0.306181] pci 0000:00:13.0: setting latency timer to 64
[ 0.306186] pci 0000:00:16.0: setting latency timer to 64
[ 0.306191] pci 0000:00:18.0: setting latency timer to 64
[ 0.306193] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.306195] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.306197] pci_bus 0000:01: resource 0 io: [0xd000-0xdfff]
[ 0.306198] pci_bus 0000:01: resource 1 mem: [0xea000000-0xedffffff]
[ 0.306200] pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.306202] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
[ 0.306203] pci_bus 0000:02: resource 1 mem: [0xefd00000-0xefdfffff]
[ 0.306205] pci_bus 0000:02: resource 2 pref mem [0xefe00000-0xefefffff]
[ 0.306207] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.306208] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[ 0.306210] pci_bus 0000:03: resource 0 io: [0xb000-0xbfff]
[ 0.306212] pci_bus 0000:03: resource 1 mem: [0xefc00000-0xefcfffff]
[ 0.306213] pci_bus 0000:03: resource 2 pref mem [0xefb00000-0xefbfffff]
[ 0.306215] pci_bus 0000:04: resource 0 io: [0xa000-0xafff]
[ 0.306216] pci_bus 0000:04: resource 1 mem: [0xefa00000-0xefafffff]
[ 0.306218] pci_bus 0000:04: resource 2 pref mem [0xef900000-0xef9fffff]
[ 0.306220] pci_bus 0000:05: resource 0 io: [0x9000-0x9fff]
[ 0.306221] pci_bus 0000:05: resource 1 mem: [0xe6000000-0xe9ffffff]
[ 0.306223] pci_bus 0000:05: resource 2 pref mem [0xc0000000-0xcfffffff]
[ 0.306240] NET: Registered protocol family 2
[ 0.306288] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.306452] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.306660] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.306764] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.306767] TCP reno registered
[ 0.306807] NET: Registered protocol family 1
[ 0.332028] pci 0000:01:00.0: Boot video device
[ 0.332067] Unpacking initramfs...
[ 0.364838] Freeing initrd memory: 1842k freed
[ 0.365310] audit: initializing netlink socket (disabled)
[ 0.365320] type=2000 audit(1290063725.363:1): initialized
[ 0.367700] highmem bounce pool size: 64 pages
[ 0.367705] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.368583] VFS: Disk quotas dquot_6.5.2
[ 0.368618] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.368665] msgmni has been set to 1711
[ 0.368787] alg: No test for stdrng (krng)
[ 0.368821] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.368825] io scheduler noop registered
[ 0.368827] io scheduler anticipatory registered
[ 0.368829] io scheduler deadline registered
[ 0.368852] io scheduler cfq registered (default)
[ 0.368956] pcieport 0000:00:03.0: irq 24 for MSI/MSI-X
[ 0.368960] pcieport 0000:00:03.0: setting latency timer to 64
[ 0.369036] pcieport 0000:00:13.0: irq 25 for MSI/MSI-X
[ 0.369040] pcieport 0000:00:13.0: setting latency timer to 64
[ 0.369117] pcieport 0000:00:16.0: irq 26 for MSI/MSI-X
[ 0.369122] pcieport 0000:00:16.0: setting latency timer to 64
[ 0.369200] pcieport 0000:00:18.0: irq 27 for MSI/MSI-X
[ 0.369205] pcieport 0000:00:18.0: setting latency timer to 64
[ 0.369410] vesafb: framebuffer at 0xeb000000, mapped to 0xf7c80000, using 6144k, total 14336k
[ 0.369414] vesafb: mode is 1024x768x32, linelength=4096, pages=1
[ 0.369417] vesafb: protected mode interface info at c000:b3e0
[ 0.369420] vesafb: pmi: set display start = c00cb443, set palette = c00cb49e
[ 0.369422] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
[ 0.369432] vesafb: scrolling: redraw
[ 0.369435] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.383834] Console: switching to colour frame buffer device 128x48
[ 0.398330] fb0: VESA VGA frame buffer device
[ 0.398478] isapnp: Scanning for PnP cards...
[ 0.707879] isapnp: No Plug & Play device found
[ 0.708853] Linux agpgart interface v0.103
[ 0.709058] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.709485] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.710067] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.710205] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.710375] mice: PS/2 mouse device common for all mice
[ 0.710552] rtc_cmos 00:05: RTC can wake from S4
[ 0.710696] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.710889] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[ 0.711078] cpuidle: using governor ladder
[ 0.711189] cpuidle: using governor menu
[ 0.711299] No iBFT detected.
[ 0.711585] TCP cubic registered
[ 0.711758] NET: Registered protocol family 10
[ 0.712158] lo: Disabled Privacy Extensions
[ 0.712455] Mobile IPv6
[ 0.712523] NET: Registered protocol family 17
[ 0.712651] Using IPI No-Shortcut mode
[ 0.712791] PM: Resume from disk failed.
[ 0.712796] registered taskstats version 1
[ 0.713317] rtc_cmos 00:05: setting system clock to 2010-11-18 07:02:06 UTC (1290063726)
[ 0.718783] Initalizing network drop monitor service
[ 0.724222] Freeing unused kernel memory: 372k freed
[ 0.729809] Write protecting the kernel text: 2500k
[ 0.735231] Write protecting the kernel read-only data: 924k
[ 0.750128] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.776192] SCSI subsystem initialized
[ 0.792222] libata version 3.00 loaded.
[ 0.795442] sata_nv 0000:00:0e.0: version 3.5
[ 0.795665] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 0.801315] sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
[ 0.807066] sata_nv 0000:00:0e.0: Using SWNCQ mode
[ 0.814249] sata_nv 0000:00:0e.0: setting latency timer to 64
[ 0.814335] scsi0 : sata_nv
[ 0.819976] scsi1 : sata_nv
[ 0.825631] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xf700 irq 23
[ 0.831356] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xf708 irq 23
[ 0.837259] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[ 0.842910] sata_nv 0000:00:0e.1: PCI INT B -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
[ 0.848638] sata_nv 0000:00:0e.1: Using SWNCQ mode
[ 0.854939] sata_nv 0000:00:0e.1: setting latency timer to 64
[ 0.855022] scsi2 : sata_nv
[ 0.860624] scsi3 : sata_nv
[ 0.866177] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xf200 irq 22
[ 0.871743] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xf208 irq 22
[ 0.877401] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
[ 0.882858] sata_nv 0000:00:0e.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
[ 0.888468] sata_nv 0000:00:0e.2: Using SWNCQ mode
[ 0.894659] sata_nv 0000:00:0e.2: setting latency timer to 64
[ 0.894743] scsi4 : sata_nv
[ 0.900205] scsi5 : sata_nv
[ 0.905675] ata5: SATA max UDMA/133 cmd 0xf100 ctl 0xf000 bmdma 0xed00 irq 21
[ 0.911198] ata6: SATA max UDMA/133 cmd 0xef00 ctl 0xee00 bmdma 0xed08 irq 21
[ 1.268014] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.285757] ata1.00: ATA-8: WDC WD5000AACS-00ZUB0, 01.01B01, max UDMA/133
[ 1.291194] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 1.304606] ata1.00: configured for UDMA/133
[ 1.310116] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AACS-0 01.0 PQ: 0 ANSI: 5
[ 1.320014] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.336013] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.348128] ata5.00: ATAPI: Optiarc BD-ROM BR-5100S, 1.02, max UDMA/66
[ 1.358707] ata3.00: ATA-8: WDC WD5000AACS-00ZUB0, 01.01B01, max UDMA/133
[ 1.364263] ata3.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 1.372643] ata5.00: configured for UDMA/66
[ 1.378599] ata3.00: configured for UDMA/133
[ 1.780013] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.804624] ata2.00: ATA-8: WDC WD5000AACS-00ZUB0, 01.01B01, max UDMA/133
[ 1.810420] ata2.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 1.832934] ata2.00: configured for UDMA/133
[ 1.838805] scsi 1:0:0:0: Direct-Access ATA WDC WD5000AACS-0 01.0 PQ: 0 ANSI: 5
[ 1.844900] scsi 2:0:0:0: Direct-Access ATA WDC WD5000AACS-0 01.0 PQ: 0 ANSI: 5
[ 2.316514] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.335524] ata4.00: ATA-8: WDC WD5000AACS-00ZUB0, 01.01B01, max UDMA/133
[ 2.341389] ata4.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 2.361402] ata4.00: configured for UDMA/133
[ 2.367290] scsi 3:0:0:0: Direct-Access ATA WDC WD5000AACS-0 01.0 PQ: 0 ANSI: 5
[ 2.373794] scsi 4:0:0:0: CD-ROM Optiarc BD-ROM BR-5100S 1.02 PQ: 0 ANSI: 5
[ 2.844015] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.856292] ata6.00: ATA-8: WDC WD10EACS-00D6B0, 01.01A01, max UDMA/133
[ 2.862150] ata6.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 2.881339] ata6.00: configured for UDMA/133
[ 2.887074] scsi 5:0:0:0: Direct-Access ATA WDC WD10EACS-00D 01.0 PQ: 0 ANSI: 5
[ 2.910590] fan PNP0C0B:00: registered as cooling_device0
[ 2.916629] ACPI: Fan [FAN] (on)
[ 2.925594] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.931804] ACPI: Thermal Zone [THRM] (40 C)
[ 3.087330] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 3.093980] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 3.093997] sd 2:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 3.094029] sd 2:0:0:0: [sdc] Write Protect is off
[ 3.094031] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 3.094045] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.094125] sdc:
[ 3.095284] sd 0:0:0:0: [sda] Write Protect is off
[ 3.095286] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.095299] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.095371] sda: sda1
[ 3.143029] sdc1
[ 3.152366] sd 3:0:0:0: [sdd] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 3.158921] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 3.169136] sd 3:0:0:0: [sdd] Write Protect is off
[ 3.175541] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3.175565] sd 5:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 3.209286] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.216559] sd 5:0:0:0: [sde] Write Protect is off
[ 3.222966] sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 3.226645] sdd:
[ 3.226760] sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.239573] sdd1
[ 3.250149] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 3.254190] sd 1:0:0:0: [sdb] Write Protect is off
[ 3.254192] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.254205] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.254283] sdb:
[ 3.255807] sde:
[ 3.256747] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.288232] sdb1 sdb2 < sde1
[ 3.294551] sdb5
[ 3.294736] sd 5:0:0:0: [sde] Attached SCSI disk
[ 3.306967] sdb6 sdb7 >
[ 3.313340] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 3.598085] PM: Starting manual resume from disk
[ 3.604603] PM: Resume from partition 8:21
[ 3.604604] PM: Checking hibernation image.
[ 3.604738] PM: Error -22 checking image file
[ 3.604739] PM: Resume from disk failed.
[ 3.663229] kjournald starting. Commit interval 5 seconds
[ 3.663235] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.018168] udevd version 125 started
[ 5.681435] processor LNXCPU:00: registered as cooling_device1
[ 5.698997] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 5.716983] processor LNXCPU:01: registered as cooling_device2
[ 5.780034] ACPI: Power Button [PWRB]
[ 5.852079] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 5.900765] i2c i2c-0: nForce2 SMBus adapter at 0x1c00
[ 5.907574] ACPI: I/O resource nForce2_smbus [0x1c80-0x1cbf] conflicts with ACPI region SM00 [0x1c80-0x1c85]
[ 5.914600] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.921784] nForce2_smbus 0000:00:0a.1: Error probing SMB2.
[ 5.972008] ACPI: Power Button [PWRF]
[ 6.052845] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 6.059953] Uniform CD-ROM driver Revision: 3.20
[ 6.124091] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 6.164253] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 6.180245] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
[ 6.187564] forcedeth 0000:00:11.0: PCI INT A -> Link[APCH] -> GSI 20 (level, low) -> IRQ 20
[ 6.194862] forcedeth 0000:00:11.0: setting latency timer to 64
[ 6.311759] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 6.368028] usbcore: registered new interface driver usbfs
[ 6.377513] sata_sil24 0000:04:00.0: version 1.1
[ 6.377753] ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16
[ 6.384985] sata_sil24 0000:04:00.0: PCI INT A -> Link[APC7] -> GSI 16 (level, low) -> IRQ 16
[ 6.399065] nv_probe: set workaround bit for reversed mac addr
[ 6.445165] usbcore: registered new interface driver hub
[ 6.494959] sata_sil24 0000:04:00.0: setting latency timer to 64
[ 6.522163] scsi6 : sata_sil24
[ 6.567251] usbcore: registered new device driver usb
[ 6.609959] scsi7 : sata_sil24
[ 6.619980] logips2pp: Detected unknown logitech mouse model 106
[ 6.628655] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.687860] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.695352] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 6.716049] ata7: SATA max UDMA/100 host m128@0xefaff000 port 0xefaf8000 irq 16
[ 6.723796] ata8: SATA max UDMA/100 host m128@0xefaff000 port 0xefafa000 irq 16
[ 6.920587] forcedeth 0000:00:11.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:1e:8c:71:63:67
[ 6.928377] forcedeth 0000:00:11.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3
[ 6.958172] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.012016] pata_amd 0000:00:0d.0: version 0.4.1
[ 7.012047] pata_amd 0000:00:0d.0: setting latency timer to 64
[ 7.021010] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 7.034109] scsi8 : pata_amd
[ 7.056435] scsi9 : pata_amd
[ 7.116367] ata9: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 7.123491] ata10: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 7.136039] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 7.208177] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 7.220769] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input4
[ 7.285676] Floppy drive(s): fd0 is 1.44M
[ 7.308038] sr 4:0:0:0: Attached scsi generic sg4 type 5
[ 7.320249] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[ 7.327584] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
[ 7.375602] FDC 0 is a post-1991 82077
[ 7.392047] sd 5:0:0:0: Attached scsi generic sg5 type 0
[ 7.403950] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[ 7.403952] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 7.440578] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 7.456705] ohci_hcd 0000:00:0b.0: irq 23, io mem 0xeffff000
[ 7.508938] ata9.00: ATA-6: ST3160023A, 3.71, max UDMA/100
[ 7.515871] ata9.00: 312581808 sectors, multi 1: LBA48
[ 7.522782] ata9.01: ATAPI: _NEC DVD_RW ND-1300A, 1.10, max UDMA/33
[ 7.526014] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.526016] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.526018] usb usb1: Product: OHCI Host Controller
[ 7.526019] usb usb1: Manufacturer: Linux 2.6.32-5-686 ohci_hcd
[ 7.526020] usb usb1: SerialNumber: 0000:00:0b.0
[ 7.526328] usb usb1: configuration #1 chosen from 1 choice
[ 7.526589] hub 1-0:1.0: USB hub found
[ 7.526596] hub 1-0:1.0: 10 ports detected
[ 7.526884] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[ 7.526888] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
[ 7.526911] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[ 7.526913] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 7.526918] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 7.526932] ehci_hcd 0000:00:0b.1: debug port 1
[ 7.526938] ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
[ 7.526943] ehci_hcd 0000:00:0b.1: irq 22, io mem 0xefffe000
[ 7.619088] ata9: nv_mode_filter: 0x3f39f&0x739f->0x739f, BIOS=0x7000 (0xc0c00000) ACPI=0x701f (60:60:0x1f)
[ 7.619092] ata9: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0c00000) ACPI=0x701f (60:60:0x1f)
[ 7.621030] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[ 7.627122] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.633066] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.639026] usb usb2: Product: EHCI Host Controller
[ 7.645020] usb usb2: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 7.651033] usb usb2: SerialNumber: 0000:00:0b.1
[ 7.651050] ata9.00: configured for UDMA/33
[ 7.662782] usb usb2: configuration #1 chosen from 1 choice
[ 7.664745] ata9.01: configured for UDMA/33
[ 7.674343] hub 2-0:1.0: USB hub found
[ 7.680060] hub 2-0:1.0: 10 ports detected
[ 7.685916] ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 21
[ 7.691563] forcedeth 0000:00:12.0: PCI INT A -> Link[AMC1] -> GSI 21 (level, low) -> IRQ 21
[ 7.697261] forcedeth 0000:00:12.0: setting latency timer to 64
[ 7.697293] nv_probe: set workaround bit for reversed mac addr
[ 7.996006] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 8.133922] usb 2-1: New USB device found, idVendor=1058, idProduct=1110
[ 8.139763] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.145706] usb 2-1: Product: My Book 1110
[ 8.151557] usb 2-1: Manufacturer: Western Digital
[ 8.157351] usb 2-1: SerialNumber: 574341565931343632393230
[ 8.163137] usb 2-1: configuration #1 chosen from 1 choice
[ 8.217109] forcedeth 0000:00:12.0: ifname eth1, PHY OUI 0x5043 @ 1, addr 00:1e:8c:71:6f:29
[ 8.223006] forcedeth 0000:00:12.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3
[ 8.288006] usb 2-3: new high speed USB device using ehci_hcd and address 3
[ 8.425903] usb 2-3: New USB device found, idVendor=1058, idProduct=1100
[ 8.431753] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.437542] usb 2-3: Product: My Book
[ 8.443220] usb 2-3: Manufacturer: Western Digital
[ 8.448881] usb 2-3: SerialNumber: 57442D574341553430303336343134
[ 8.454608] usb 2-3: configuration #1 chosen from 1 choice
[ 8.772017] ata7: SATA link down (SStatus 0 SControl 0)
[ 10.856017] ata8: SATA link down (SStatus 0 SControl 0)
[ 10.861676] scsi 8:0:0:0: Direct-Access ATA ST3160023A 3.71 PQ: 0 ANSI: 5
[ 10.867492] sd 8:0:0:0: Attached scsi generic sg6 type 0
[ 10.868614] sd 8:0:0:0: [sdf] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 10.868647] sd 8:0:0:0: [sdf] Write Protect is off
[ 10.868649] sd 8:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 10.868663] sd 8:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.868745] sdf: sdf1
[ 10.897583] scsi 8:0:1:0: CD-ROM _NEC DVD_RW ND-1300A 1.10 PQ: 0 ANSI: 5
[ 10.897624] sd 8:0:0:0: [sdf] Attached SCSI disk
[ 10.913464] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 10.919468] sr 8:0:1:0: Attached scsi CD-ROM sr1
[ 10.919496] sr 8:0:1:0: Attached scsi generic sg7 type 5
[ 10.925566] ata10: port disabled. ignoring.
[ 10.990476] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 10.996531] firewire_ohci 0000:02:0b.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
[ 11.078843] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
[ 11.084982] HDA Intel 0000:00:0f.1: PCI INT B -> Link[AAZA] -> GSI 20 (level, low) -> IRQ 20
[ 11.103721] hda_intel: Disable MSI for Nvidia chipset
[ 11.109983] firewire_ohci: Added fw-ohci device 0000:02:0b.0, OHCI version 1.10
[ 11.114028] HDA Intel 0000:00:0f.1: setting latency timer to 64
[ 11.120425] Initializing USB Mass Storage driver...
[ 11.131851] scsi10 : SCSI emulation for USB Mass Storage devices
[ 11.138428] usb-storage: device found at 2
[ 11.138429] usb-storage: waiting for device to settle before scanning
[ 11.138442] scsi11 : SCSI emulation for USB Mass Storage devices
[ 11.145552] usbcore: registered new interface driver usb-storage
[ 11.152069] USB Mass Storage support registered.
[ 11.152123] usb-storage: device found at 3
[ 11.152124] usb-storage: waiting for device to settle before scanning
[ 11.616049] firewire_core: created device fw0: GUID 001e8c000019c3e5, S400
[ 11.940573] hda_codec: AD1988B: BIOS auto-probing.
[ 11.947077] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:0f.1/input/input5
[ 13.678839] Adding 19607292k swap on /dev/sdb5. Priority:-1 extents:1 across:19607292k
[ 14.268219] EXT3 FS on sdb1, internal journal
[ 14.650359] loop: module loaded
[ 16.136673] usb-storage: device scan complete
[ 16.138670] scsi 10:0:0:0: Direct-Access WD My Book 1110 1030 PQ: 0 ANSI: 4
[ 16.146668] scsi 10:0:0:1: CD-ROM WD Virtual CD 1110 1030 PQ: 0 ANSI: 4
[ 16.153665] usb-storage: device scan complete
[ 16.154667] scsi 10:0:0:2: Enclosure WD SES Device 1030 PQ: 0 ANSI: 4
[ 16.155668] scsi 11:0:0:0: Direct-Access WD 10EAVS External 1.65 PQ: 0 ANSI: 4
[ 16.168310] sd 10:0:0:0: Attached scsi generic sg8 type 0
[ 16.176039] sd 10:0:0:0: [sdg] 3905656832 512-byte logical blocks: (1.99 TB/1.81 TiB)
[ 16.184536] sr2: scsi3-mmc drive: 51x/51x caddy
[ 16.196574] sr 10:0:0:1: Attached scsi CD-ROM sr2
[ 16.196607] sr 10:0:0:1: Attached scsi generic sg9 type 5
[ 16.198532] sd 10:0:0:0: [sdg] Write Protect is off
[ 16.198534] sd 10:0:0:0: [sdg] Mode Sense: 23 00 10 00
[ 16.198535] sd 10:0:0:0: [sdg] Assuming drive cache: write through
[ 16.201531] sd 10:0:0:0: [sdg] Assuming drive cache: write through
[ 16.201532] sdg: sdg1
[ 16.260096] scsi 10:0:0:2: Attached scsi generic sg10 type 13
[ 16.268483] sd 11:0:0:0: Attached scsi generic sg11 type 0
[ 16.278804] sd 10:0:0:0: [sdg] Assuming drive cache: write through
[ 16.285148] sd 10:0:0:0: [sdg] Attached SCSI disk
[ 16.291906] sd 11:0:0:0: [sdh] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 16.306529] sd 11:0:0:0: [sdh] Write Protect is off
[ 16.312733] sd 11:0:0:0: [sdh] Mode Sense: 21 00 00 00
[ 16.312734] sd 11:0:0:0: [sdh] Assuming drive cache: write through
[ 16.323782] sd 11:0:0:0: [sdh] Assuming drive cache: write through
[ 16.329953] sdh: sdh1
[ 16.348820] sd 11:0:0:0: [sdh] Assuming drive cache: write through
[ 16.354990] sd 11:0:0:0: [sdh] Attached SCSI disk
[ 16.371494] ses 10:0:0:2: Attached Enclosure device
[ 16.491718] kjournald starting. Commit interval 5 seconds
[ 16.497848] EXT3 FS on sdb6, internal journal
[ 16.503917] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.537914] kjournald starting. Commit interval 5 seconds
[ 16.543948] EXT3 FS on sdb7, internal journal
[ 16.549945] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.616585] kjournald starting. Commit interval 5 seconds
[ 16.622446] EXT3 FS on sde1, internal journal
[ 16.628225] EXT3-fs: mounted filesystem with ordered data mode.
[ 17.998719] RPC: Registered udp transport module.
[ 18.004880] RPC: Registered tcp transport module.
[ 18.011069] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 18.089321] Slow work thread pool: Starting up
[ 18.095452] Slow work thread pool: Ready
[ 18.101514] FS-Cache: Loaded
[ 18.155017] FS-Cache: Netfs 'nfs' registered for caching
[ 18.194431] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 18.594241] forcedeth 0000:00:11.0: irq 28 for MSI/MSI-X
[ 20.902096] lp: driver loaded but no devices found
[ 20.956589] ppdev: user-space parallel port driver
[ 22.311075] svc: failed to register lockdv1 RPC service (errno 97).
[ 22.317848] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 22.326757] NFSD: starting 90-second grace period
[ 27.301288] forcedeth 0000:00:12.0: irq 29 for MSI/MSI-X
[ 27.301471] eth1: no link during initialization.
[ 27.308156] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 28.809077] NET: Registered protocol family 5
[ 30.543837] nvidia: module license 'NVIDIA' taints kernel.
[ 30.543840] Disabling lock debugging due to kernel taint
[ 31.353228] ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
[ 31.353232] nvidia 0000:01:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
[ 31.353237] nvidia 0000:01:00.0: setting latency timer to 64
[ 31.353241] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 31.353242] vgaarb: transferring owner from PCI:0000:01:00.0 to PCI:0000:05:00.0
[ 31.353333] nvidia 0000:05:00.0: enabling device (0000 -> 0003)
[ 31.353337] nvidia 0000:05:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
[ 31.353342] nvidia 0000:05:00.0: setting latency timer to 64
[ 31.353347] vgaarb: device changed decodes: PCI:0000:05:00.0,olddecodes=io+mem,decodes=none:owns=none
[ 31.353432] NVRM: loading NVIDIA UNIX x86 Kernel Module 256.35 Wed Jun 16 18:57:17 PDT 2010
[ 42.300002] eth0: no IPv6 routers present
[ 81.639084] UDF-fs: Partition marked readonly; forcing readonly mount
[ 81.639456] UDF-fs INFO UDF: Mounting volume 'WD SmartWare', timestamp 2009/10/14 22:49 (103c)
Den sidste linje i outputtet er systemet der monterer det cd-image der ligger på den ene USB-harddisk, så jeg ville tro at den del hvor den fejler kommer lige bagefter. Jeg har prøvet at lede efter noget i sysloggen, men det ser ud til at den kun skriver om de to harddiske hvis det lykkedes dem at blive monteret.
Da jeg opdagede fejlen tænkte jeg egentlig bare at jeg ville vente og se hvad der skete når den nye Debian kommer ud om en måned eller to. Desværre ser det ud til at den stabile version kommer til at køre med den kernel jeg bruger nu, det er derfor jeg havde håbet på at få det til at virke.
)