Manglende lyd i ubuntu 9.04

[Hans Olsen]

Hej linux folk håber i kan hjælpe mig med lydopsætning i medion 96420.

Jeg har fulgt soundpartner,s opsætning (dk/forum/viewtopic.php?f=3&t=4371&st=0&sk=t&sd=a&start=30) men når jeg kommer frem til
sudo gedit /etc/modprobe.d/alsa-base er der ikke nogen fil eller skrift, gedit åbner godt nok men blank. hvad gør jeg event. forkert

[ChrisBuchholz]

Hej linux folk håber i kan hjælpe mig med lydopsætning i medion 96420.

Jeg har fulgt soundpartner,s opsætning (dk/forum/viewtopic.php?f=3&t=4371&st=0&sk=t&sd=a&start=30) men når jeg kommer frem til
sudo gedit /etc/modprobe.d/alsa-base er der ikke nogen fil eller skrift, gedit åbner godt nok men blank. hvad gør jeg event. forkert

Jeg har faktisk postet dette på launchpad, men jeg kan lige nævne det her igen. I 9.04+ SKAL alle konfigurations filer ende med .conf. Dvs., at "/etc/modprobe.d/alsa-base" nu hedder "/etc/modprobe.d/alsa-base.conf", så det er nu denne fil du skal have fat i.

Hvis du er rigtig rar, kunne du også lige poste dette i den tråd du linker til, så der er andre end dig der får lykke af løsningen:)

[soundpartner]

Hej linux folk håber i kan hjælpe mig med lydopsætning i medion 96420.

Jeg har fulgt soundpartner,s opsætning (dk/forum/viewtopic.php?f=3&t=4371&st=0&sk=t&sd=a&start=30) men når jeg kommer frem til
sudo gedit /etc/modprobe.d/alsa-base er der ikke nogen fil eller skrift, gedit åbner godt nok men blank. hvad gør jeg event. forkert

Jeg har faktisk postet dette på launchpad, men jeg kan lige nævne det her igen. I 9.04+ SKAL alle konfigurations filer ende med .conf. Dvs., at "/etc/modprobe.d/alsa-base" nu hedder "/etc/modprobe.d/alsa-base.conf", så det er nu denne fil du skal have fat i.

Hvis du er rigtig rar, kunne du også lige poste dette i den tråd du linker til, så der er andre end dig der for lykke af løsningen:)

korrekt...
dette betyder ay med 9.04 får vi en del at lave for mange af alle de kendte løsninger fundet på forum de vil ikke virke i 9.04

[Hans Olsen]

Tak for jeres svar
Har nu prøvet lidt forskelligt men kan ikke få det til at virke her er et output.

0.813191] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.813332] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.813782] ACPI: WMI: Mapper loaded
[ 0.813820] SCSI subsystem initialized
[ 0.813820] libata version 3.00 loaded.
[ 0.813820] usbcore: registered new interface driver usbfs
[ 0.813820] usbcore: registered new interface driver hub
[ 0.813820] usbcore: registered new device driver usb
[ 0.813820] PCI: Using ACPI for IRQ routing
[ 0.816015] Bluetooth: Core ver 2.13
[ 0.816021] NET: Registered protocol family 31
[ 0.816021] Bluetooth: HCI device and connection manager initialized
[ 0.816021] Bluetooth: HCI socket layer initialized
[ 0.816023] NET: Registered protocol family 8
[ 0.816025] NET: Registered protocol family 20
[ 0.816039] NetLabel: Initializing
[ 0.816042] NetLabel: domain hash size = 128
[ 0.816044] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.816061] NetLabel: unlabeled traffic allowed by default
[ 0.816079] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.816085] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.820085] AppArmor: AppArmor Filesystem Enabled
[ 0.824013] Switched to high resolution mode on CPU 0
[ 0.824606] Switched to high resolution mode on CPU 1
[ 0.824617] pnp: PnP ACPI init
[ 0.824627] ACPI: bus type pnp registered
[ 0.944391] pnp: PnP ACPI: found 10 devices
[ 0.944394] ACPI: ACPI bus type pnp unregistered
[ 0.944399] PnPBIOS: Disabled by ACPI PNP
[ 0.944412] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.944416] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.944420] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.944423] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.944427] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.944430] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.944433] system 00:01: iomem range 0xfed40000-0xfed44fff has been reserved
[ 0.944437] system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.944446] system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.944454] system 00:06: ioport range 0x680-0x69f has been reserved
[ 0.944458] system 00:06: ioport range 0x800-0x80f has been reserved
[ 0.944461] system 00:06: ioport range 0x1000-0x107f has been reserved
[ 0.944465] system 00:06: ioport range 0x1180-0x11bf has been reserved
[ 0.944468] system 00:06: ioport range 0x1640-0x164f has been reserved
[ 0.944471] system 00:06: ioport range 0xfe00-0xfe00 has been reserved
[ 0.979256] pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
[ 0.979259] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.979263] pci 0000:00:01.0: IO window: 0x2000-0x2fff
[ 0.979268] pci 0000:00:01.0: MEM window: 0xcc000000-0xceffffff
[ 0.979273] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.979279] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.979284] pci 0000:00:1c.0: IO window: 0x3000-0x3fff
[ 0.979291] pci 0000:00:1c.0: MEM window: 0xf6000000-0xf7ffffff
[ 0.979297] pci 0000:00:1c.0: PREFETCH window: 0x000000f0000000-0x000000f1ffffff
[ 0.979307] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[ 0.979311] pci 0000:00:1c.2: IO window: 0x4000-0x4fff
[ 0.979318] pci 0000:00:1c.2: MEM window: 0xf8000000-0xf9ffffff
[ 0.979324] pci 0000:00:1c.2: PREFETCH window: 0x000000f2000000-0x000000f3ffffff
[ 0.979333] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:06
[ 0.979337] pci 0000:00:1c.3: IO window: 0x5000-0x5fff
[ 0.979345] pci 0000:00:1c.3: MEM window: 0xfa000000-0xfbffffff
[ 0.979351] pci 0000:00:1c.3: PREFETCH window: 0x000000f4000000-0x000000f5ffffff
[ 0.979360] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:08
[ 0.979362] pci 0000:00:1e.0: IO window: disabled
[ 0.979369] pci 0000:00:1e.0: MEM window: disabled
[ 0.979375] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.979391] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.979396] pci 0000:00:01.0: setting latency timer to 64
[ 0.979407] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.979413] pci 0000:00:1c.0: setting latency timer to 64
[ 0.979424] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.979430] pci 0000:00:1c.2: setting latency timer to 64
[ 0.979441] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.979447] pci 0000:00:1c.3: setting latency timer to 64
[ 0.979456] pci 0000:00:1e.0: setting latency timer to 64
[ 0.979461] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.979464] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.979467] bus: 01 index 0 io port: [0x2000-0x2fff]
[ 0.979469] bus: 01 index 1 mmio: [0xcc000000-0xceffffff]
[ 0.979472] bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
[ 0.979475] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.979477] bus: 02 index 0 io port: [0x3000-0x3fff]
[ 0.979480] bus: 02 index 1 mmio: [0xf6000000-0xf7ffffff]
[ 0.979482] bus: 02 index 2 mmio: [0xf0000000-0xf1ffffff]
[ 0.979485] bus: 02 index 3 mmio: [0x0-0x0]
[ 0.979488] bus: 04 index 0 io port: [0x4000-0x4fff]
[ 0.979490] bus: 04 index 1 mmio: [0xf8000000-0xf9ffffff]
[ 0.979493] bus: 04 index 2 mmio: [0xf2000000-0xf3ffffff]
[ 0.979495] bus: 04 index 3 mmio: [0x0-0x0]
[ 0.979498] bus: 06 index 0 io port: [0x5000-0x5fff]
[ 0.979500] bus: 06 index 1 mmio: [0xfa000000-0xfbffffff]
[ 0.979503] bus: 06 index 2 mmio: [0xf4000000-0xf5ffffff]
[ 0.979505] bus: 06 index 3 mmio: [0x0-0x0]
[ 0.979508] bus: 08 index 0 mmio: [0x0-0x0]
[ 0.979510] bus: 08 index 1 mmio: [0x0-0x0]
[ 0.979512] bus: 08 index 2 mmio: [0x0-0x0]
[ 0.979514] bus: 08 index 3 io port: [0x00-0xffff]
[ 0.979517] bus: 08 index 4 mmio: [0x000000-0xffffffff]
[ 0.979527] NET: Registered protocol family 2
[ 0.992064] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.992362] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.992748] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.992957] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.992960] TCP reno registered
[ 0.996083] NET: Registered protocol family 1
[ 0.996223] checking if image is initramfs... it is
[ 1.794746] Freeing initrd memory: 7368k freed
[ 1.794791] Simple Boot Flag at 0x36 set to 0x1
[ 1.794984] cpufreq: No nForce2 chipset.
[ 1.795143] audit: initializing netlink socket (disabled)
[ 1.795162] type=2000 audit(1240706112.792:1): initialized
[ 1.804480] highmem bounce pool size: 64 pages
[ 1.804486] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.806190] VFS: Disk quotas dquot_6.5.1
[ 1.806264] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.807030] fuse init (API version 7.10)
[ 1.807139] msgmni has been set to 1698
[ 1.807355] alg: No test for stdrng (krng)
[ 1.807370] io scheduler noop registered
[ 1.807373] io scheduler anticipatory registered
[ 1.807375] io scheduler deadline registered
[ 1.807392] io scheduler cfq registered (default)
[ 1.807607] pci 0000:01:00.0: Boot video device
[ 2.048480] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 2.048529] pcieport-driver 0000:00:01.0: found MSI capability
[ 2.048560] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[ 2.048572] pci_express 0000:00:01.0:pcie00: allocate port service
[ 2.048591] pci_express 0000:00:01.0:pcie02: allocate port service
[ 2.048611] pci_express 0000:00:01.0:pcie03: allocate port service
[ 2.048678] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 2.048737] pcieport-driver 0000:00:1c.0: found MSI capability
[ 2.048777] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[ 2.048796] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 2.048812] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 2.048827] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 2.048915] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 2.048974] pcieport-driver 0000:00:1c.2: found MSI capability
[ 2.049013] pcieport-driver 0000:00:1c.2: irq 2301 for MSI/MSI-X
[ 2.049032] pci_express 0000:00:1c.2:pcie00: allocate port service
[ 2.049048] pci_express 0000:00:1c.2:pcie02: allocate port service
[ 2.049063] pci_express 0000:00:1c.2:pcie03: allocate port service
[ 2.049151] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 2.049210] pcieport-driver 0000:00:1c.3: found MSI capability
[ 2.049249] pcieport-driver 0000:00:1c.3: irq 2300 for MSI/MSI-X
[ 2.049268] pci_express 0000:00:1c.3:pcie00: allocate port service
[ 2.049283] pci_express 0000:00:1c.3:pcie02: allocate port service
[ 2.049299] pci_express 0000:00:1c.3:pcie03: allocate port service
[ 2.049401] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.049812] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 2.168079] ACPI: AC Adapter [AC] (on-line)
[ 2.532215] ACPI: Battery Slot [BAT0] (battery present)
[ 2.532302] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 2.532306] ACPI: Power Button (FF) [PWRF]
[ 2.532376] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 2.532387] ACPI: Power Button (CM) [PWRB]
[ 2.532438] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 2.532815] ACPI: Lid Switch [LID0]
[ 2.532872] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[ 2.532875] ACPI: Sleep Button (CM) [SLPB]
[ 2.533582] ACPI: SSDT 7FED5C79, 01B4 (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 2.534060] ACPI: SSDT 7FED55EB, 0609 (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 2.536827] Monitor-Mwait will be used to enter C-1 state
[ 2.536832] Monitor-Mwait will be used to enter C-2 state
[ 2.536835] Monitor-Mwait will be used to enter C-3 state
[ 2.536855] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.536885] processor ACPI_CPU:00: registered as cooling_device0
[ 2.536890] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.537320] ACPI: SSDT 7FED5E2D, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624)
[ 2.537757] ACPI: SSDT 7FED5BF4, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624)
[ 2.538939] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.538963] processor ACPI_CPU:01: registered as cooling_device1
[ 2.538968] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.661503] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.662369] ACPI: Thermal Zone [TZ00] (53 C)
[ 2.662789] thermal LNXTHERM:02: registered as thermal_zone1
[ 2.662950] ACPI: Thermal Zone [TZ01] (56 C)
[ 2.663022] isapnp: Scanning for PnP cards...
[ 3.018138] isapnp: No Plug & Play device found
[ 3.032296] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 3.033580] brd: module loaded
[ 3.033967] loop: module loaded
[ 3.034050] Fixed MDIO Bus: probed
[ 3.034056] PPP generic driver version 2.4.2
[ 3.034124] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 3.034160] Driver 'sd' needs updating - please use bus_type methods
[ 3.034172] Driver 'sr' needs updating - please use bus_type methods
[ 3.034260] ata_piix 0000:00:1f.1: version 2.12
[ 3.034270] ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.034314] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3.034398] scsi0 : ata_piix
[ 3.034499] scsi1 : ata_piix
[ 3.035261] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
[ 3.035265] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
[ 3.212442] ata1.00: ATAPI: TSSTcorp CDDVDW SN-S082H, SB00, max UDMA/33
[ 3.244373] ata1.00: configured for UDMA/33
[ 3.415006] scsi 0:0:0:0: CD-ROM TSSTcorp CDDVDW SN-S082H SB00 PQ: 0 ANSI: 5
[ 3.431134] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.431138] Uniform CD-ROM driver Revision: 3.20
[ 3.431245] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 3.431297] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 3.431320] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.431325] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 3.584035] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 3.584100] scsi2 : ata_piix
[ 3.584176] scsi3 : ata_piix
[ 3.585559] ata3: SATA max UDMA/133 cmd 0x18f8 ctl 0x18cc bmdma 0x18e0 irq 19
[ 3.585568] ata4: SATA max UDMA/133 cmd 0x18f0 ctl 0x18c8 bmdma 0x18e8 irq 19
[ 4.380091] ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.380110] ata3.01: SATA link down (SStatus 0 SControl 300)
[ 4.435630] ata3.00: ATA-8: WDC WD2500BEVS-22UST0, 01.01A01, max UDMA/133
[ 4.435633] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 4.449283] ata3.00: configured for UDMA/133
[ 5.099284] ata4.00: SATA link down (SStatus 0 SControl 300)
[ 5.099299] ata4.01: SATA link down (SStatus 0 SControl 0)
[ 5.099391] scsi 2:0:0:0: Direct-Access ATA WDC WD2500BEVS-2 01.0 PQ: 0 ANSI: 5
[ 5.099509] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 5.099529] sd 2:0:0:0: [sda] Write Protect is off
[ 5.099532] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.099564] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.099631] sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 5.099649] sd 2:0:0:0: [sda] Write Protect is off
[ 5.099652] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.099683] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.099687] sda: sda1 sda2 < sda5 sda6 > sda3
[ 5.177182] sd 2:0:0:0: [sda] Attached SCSI disk
[ 5.177231] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 5.178047] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.178072] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 5.178094] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 5.178098] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 5.178167] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 5.182079] ehci_hcd 0000:00:1a.7: debug port 1
[ 5.182088] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 5.182105] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc204000
[ 5.196011] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 5.196087] usb usb1: configuration #1 chosen from 1 choice
[ 5.196123] hub 1-0:1.0: USB hub found
[ 5.196131] hub 1-0:1.0: 4 ports detected
[ 5.196261] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 5.196274] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 5.196278] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 5.196330] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 5.200239] ehci_hcd 0000:00:1d.7: debug port 1
[ 5.200248] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 5.200263] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc204400
[ 5.212012] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 5.212091] usb usb2: configuration #1 chosen from 1 choice
[ 5.212130] hub 2-0:1.0: USB hub found
[ 5.212137] hub 2-0:1.0: 6 ports detected
[ 5.212253] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.212273] uhci_hcd: USB Universal Host Controller Interface driver
[ 5.212300] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.212308] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 5.212312] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 5.212371] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 5.212411] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[ 5.212501] usb usb3: configuration #1 chosen from 1 choice
[ 5.212533] hub 3-0:1.0: USB hub found
[ 5.212543] hub 3-0:1.0: 2 ports detected
[ 5.212657] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 5.212665] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 5.212670] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 5.212719] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 5.212757] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[ 5.212845] usb usb4: configuration #1 chosen from 1 choice
[ 5.212879] hub 4-0:1.0: USB hub found
[ 5.212886] hub 4-0:1.0: 2 ports detected
[ 5.212989] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 5.212996] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 5.213007] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 5.213058] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 5.213086] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 5.213184] usb usb5: configuration #1 chosen from 1 choice
[ 5.213216] hub 5-0:1.0: USB hub found
[ 5.213225] hub 5-0:1.0: 2 ports detected
[ 5.213325] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 5.213333] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 5.213337] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 5.213389] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 5.213418] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
[ 5.213504] usb usb6: configuration #1 chosen from 1 choice
[ 5.213535] hub 6-0:1.0: USB hub found
[ 5.213542] hub 6-0:1.0: 2 ports detected
[ 5.213644] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 5.213652] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 5.213656] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 5.213706] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 5.213735] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
[ 5.213824] usb usb7: configuration #1 chosen from 1 choice
[ 5.213857] hub 7-0:1.0: USB hub found
[ 5.213866] hub 7-0:1.0: 2 ports detected
[ 5.214024] usbcore: registered new interface driver libusual
[ 5.214060] usbcore: registered new interface driver usbserial
[ 5.214076] USB Serial support registered for generic
[ 5.214096] usbcore: registered new interface driver usbserial_generic
[ 5.214099] usbserial: USB Serial Driver core
[ 5.214159] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 5.216765] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 5.217839] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.217845] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 5.217849] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 5.217852] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 5.217855] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 5.224046] mice: PS/2 mouse device common for all mice
[ 5.244128] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 5.244163] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 5.244234] device-mapper: uevent: version 1.0.3
[ 5.244350] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 5.244436] device-mapper: multipath: version 1.0.5 loaded
[ 5.244439] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 5.244529] EISA: Probing bus 0 at eisa.0
[ 5.244536] Cannot allocate resource for EISA slot 1
[ 5.244540] Cannot allocate resource for EISA slot 2
[ 5.244543] Cannot allocate resource for EISA slot 3
[ 5.244545] Cannot allocate resource for EISA slot 4
[ 5.244548] Cannot allocate resource for EISA slot 5
[ 5.244565] EISA: Detected 0 cards.
[ 5.244708] cpuidle: using governor ladder
[ 5.244859] cpuidle: using governor menu
[ 5.245500] TCP cubic registered
[ 5.245622] NET: Registered protocol family 10
[ 5.246153] lo: Disabled Privacy Extensions
[ 5.246583] NET: Registered protocol family 17
[ 5.246604] Bluetooth: L2CAP ver 2.11
[ 5.246606] Bluetooth: L2CAP socket layer initialized
[ 5.246610] Bluetooth: SCO (Voice Link) ver 0.6
[ 5.246612] Bluetooth: SCO socket layer initialized
[ 5.246647] Bluetooth: RFCOMM socket layer initialized
[ 5.246654] Bluetooth: RFCOMM TTY layer initialized
[ 5.246657] Bluetooth: RFCOMM ver 1.10
[ 5.246702] Marking TSC unstable due to TSC halts in idle
[ 5.247431] Using IPI No-Shortcut mode
[ 5.247514] registered taskstats version 1
[ 5.247652] Magic number: 5:965:557
[ 5.247741] rtc_cmos 00:07: setting system clock to 2009-04-26 00:35:17 UTC (1240706117)
[ 5.247745] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 5.247748] EDD information not available.
[ 5.248063] Freeing unused kernel memory: 532k freed
[ 5.248254] Write protecting the kernel text: 4128k
[ 5.248327] Write protecting the kernel read-only data: 1532k
[ 5.276901] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 5.508116] usb 1-4: new high speed USB device using ehci_hcd and address 2
[ 5.682645] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 5.682803] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 5.682976] r8169 0000:04:00.0: setting latency timer to 64
[ 5.684479] r8169 0000:04:00.0: irq 2299 for MSI/MSI-X
[ 5.685812] eth0: RTL8101e at 0xf7c7c000, 00:40:d0:e4:fe:7b, XID 34200000 IRQ 2299
[ 5.723026] usb 1-4: configuration #1 chosen from 1 choice
[ 5.729088] Initializing USB Mass Storage driver...
[ 5.737069] scsi4 : SCSI emulation for USB Mass Storage devices
[ 5.737593] usbcore: registered new interface driver usb-storage
[ 5.737597] USB Mass Storage support registered.
[ 5.737701] usb-storage: device found at 2
[ 5.737703] usb-storage: waiting for device to settle before scanning
[ 5.892074] usb 2-5: new high speed USB device using ehci_hcd and address 3
[ 6.042439] usb 2-5: configuration #1 chosen from 1 choice
[ 6.436044] usb 6-1: new low speed USB device using uhci_hcd and address 2
[ 6.490730] PM: Starting manual resume from disk
[ 6.490735] PM: Resume from partition 8:6
[ 6.490737] PM: Checking hibernation image.
[ 6.490978] PM: Resume from disk failed.
[ 6.527510] kjournald starting. Commit interval 5 seconds
[ 6.527527] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.636582] usb 6-1: configuration #1 chosen from 1 choice
[ 6.884075] usb 7-2: new full speed USB device using uhci_hcd and address 2
[ 7.070901] usb 7-2: configuration #1 chosen from 1 choice
[ 10.737258] usb-storage: device scan complete
[ 10.743238] scsi 4:0:0:0: Direct-Access Generic- SD/MMC/MS/MSPro 1.00 PQ: 0 ANSI: 0 CCS
[ 10.744832] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 10.744902] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 10.921657] udev: starting version 141
[ 11.063037] acpi device:05: registered as cooling_device2
[ 11.063563] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/device:03/input/input6
[ 11.068152] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 11.156992] Linux agpgart interface v0.103
[ 11.427828] rt2860sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 11.431127] rt2860 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 11.431248]
[ 11.431249]
[ 11.431250] === pAd = f7e6e000, size = 580788 ===
[ 11.431251]
[ 11.431253] <-- RTMPAllocAdapterBlock, Status=0
[ 11.431392] rt2860 0000:02:00.0: setting latency timer to 64
[ 11.449487] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 11.449612] usbcore: registered new interface driver btusb
[ 11.456569] usbcore: registered new interface driver hiddev
[ 11.495921] input: HID 04d9:0499 as /devices/pci0000:00/0000:00:1d.1/usb6/6-1/6-1:1.0/input/input7
[ 11.497193] generic-usb 0003:04D9:0499.0001: input,hidraw0: USB HID v1.10 Mouse [HID 04d9:0499] on usb-0000:00:1d.1-1/input0
[ 11.497223] usbcore: registered new interface driver usbhid
[ 11.497253] usbhid: v2.6:USB HID core driver
[ 11.654785] nvidia: module license 'NVIDIA' taints kernel.
[ 11.909146] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 11.909164] nvidia 0000:01:00.0: setting latency timer to 64
[ 11.910432] NVRM: loading NVIDIA UNIX x86 Kernel Module 180.44 Mon Mar 23 14:59:10 PST 2009
[ 11.919000] iTCO_vendor_support: vendor-support=0
[ 12.099408] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 12.121165] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 12.121365] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 12.121504] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 12.194539] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 12.599167] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 12.599258] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 12.639515] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 12.640122] hda_codec: Cannot set up configuration from BIOS. Using base mode...
[ 12.641317] SPDIF already defined
[ 12.737051] HDA Intel 0000:00:1b.0: PCI INT A disabled
[ 12.737062] HDA Intel: probe of 0000:00:1b.0 failed with error -16
[ 12.871928] lp: driver loaded but no devices found
[ 12.965503] Adding 3301316k swap on /dev/sda6. Priority:-1 extents:1 across:3301316k
[ 13.000019] Clocksource tsc unstable (delta = -139941333 ns)
[ 13.053451] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x92a0b1, caps: 0xa04713/0x200000
[ 13.089138] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
[ 13.624661] EXT3 FS on sda5, internal journal
[ 14.810164] type=1505 audit(1240698927.060:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2102
[ 14.869168] type=1505 audit(1240698927.121:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2106
[ 14.869282] type=1505 audit(1240698927.121:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2106
[ 14.869335] type=1505 audit(1240698927.121:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2106
[ 14.869382] type=1505 audit(1240698927.121:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2106
[ 15.033000] type=1505 audit(1240698927.281:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2111
[ 15.033221] type=1505 audit(1240698927.285:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2111
[ 15.068028] type=1505 audit(1240698927.317:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2115
[ 18.022293] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 18.022296] Bluetooth: BNEP filters: protocol multicast
[ 18.033284] Bridge firewalling registered
[ 19.187605] ppdev: user-space parallel port driver
[ 21.528233] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 21.528347] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 21.583442] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 21.583990] hda_codec: Cannot set up configuration from BIOS. Using base mode...
[ 21.585242] SPDIF already defined
[ 22.573344] HDA Intel 0000:00:1b.0: PCI INT A disabled
[ 22.573359] HDA Intel: probe of 0000:00:1b.0 failed with error -16
[ 22.873468] r8169: eth0: link down
[ 22.873732] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.879831] RX DESC f5de3000 size = 2048
[ 22.880059] <-- RTMPAllocTxRxRingMemory, Status=0
[ 22.884019] --> Error 2 opening /etc/Wireless/RT2860STA/RT2860STA.dat
[ 22.884022] 1. Phy Mode = 0
[ 22.884024] 2. Phy Mode = 0
[ 22.904346] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 22.910079] 3. Phy Mode = 0
[ 22.914686] MCS Set = 00 00 00 00 00
[ 22.916285] <==== RTMPInitialize, Status=0
[ 22.916353] 0x1300 = 00073200
[ 27.965751] ===>rt_ioctl_giwscan. 4(4) BSS returned, data->length = 473
[ 33.008042] ra0: no IPv6 routers present
[ 47.759479] ===>rt_ioctl_giwscan. 3(3) BSS returned, data->length = 351
[ 57.765822] ===>rt_ioctl_giwscan. 4(4) BSS returned, data->length = 473
[ 57.766048] ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=11)
[ 77.765051] ===>rt_ioctl_giwscan. 4(4) BSS returned, data->length = 473

[ChrisBuchholz]

Nu har jeg ikke læst dit nyeste indlæg igennem, trådstarter, da kl er 04:49 og jeg tog afsted til Ubuntu Live! kl 6 i morges og er først lige kommet hjem, men med dit lydkort skulle det gerne virke hvis du gør følgende og derefter genstarter...

* Tilføj "options snd-hda-intel model=laptop-eapd probe_mask=1" i bunden af filen /etc/modprobe.d/alsa-base.conf som du selvfølgelig husker at åbne som superuser (alt+f2 > gksu gedit /etc/modprobe.d/alsa-base.conf)
* sudo rmmod snd-hda-intel
* sudo modprobe snd-hda-intel model=medion probe_mask=1

[rasmusberg]

Jeg har ingen lyd i Amarok 2 (og kun der). Jeg har på en måde ikke lyst til at selv gøre noget for at rette problemet, synes at den slags skal bare virke (også selvom det er gratis) og burde ikke være brugeren der skal sidde og indsætte diverse koder for at det funker...

[ChrisBuchholz]

Jeg har ingen lyd i Amarok 2 (og kun der). Jeg har på en måde ikke lyst til at selv gøre noget for at rette problemet, synes at den slags skal bare virke (også selvom det er gratis) og burde ikke være brugeren der skal sidde og indsætte diverse koder for at det funker...

Ja helt sikkert - det burde virker out-of-box, men det gør det bare ikke på noget hardware. Den computer jeg sidder på nu, min main, har været en laban at få til at virke med fn+* keys, lyd og wifi samt andet på tidligere versioner, men det bliver bedre og bedre for hver release, og på jaunty er det eneste der _ikke_ virker lydkortet, der så kan fikses med det hack jeg smed tidligere.

Ang. Amarok - har du været inde og rode i noget? Anyways, det er nok bare at du skal være den rigtige lydserver eller sådan noget.

[rasmusberg]

Jeg har ingen lyd i Amarok 2 (og kun der). Jeg har på en måde ikke lyst til at selv gøre noget for at rette problemet, synes at den slags skal bare virke (også selvom det er gratis) og burde ikke være brugeren der skal sidde og indsætte diverse koder for at det funker...

Ja helt sikkert - det burde virker out-of-box, men det gør det bare ikke på noget hardware. Den computer jeg sidder på nu, min main, har været en laban at få til at virke med fn+* keys, lyd og wifi samt andet på tidligere versioner, men det bliver bedre og bedre for hver release, og på jaunty er det eneste der _ikke_ virker lydkortet, der så kan fikses med det hack jeg smed tidligere.

Ang. Amarok - har du været inde og rode i noget? Anyways, det er nok bare at du skal være den rigtige lydserver eller sådan noget.

Det var ikke så hårdt ment som jeg skrev det. Jeg har ikke rigtigt prøvet på noget endnu og det vil jeg selvfølgelig... Kan være jeg vender tilbage hvis dit råd eller andet jeg finder frem til ikke virker...

[Hans Olsen]

Hej ChrisBuchholz du skal ha rigtig mange tak for hjælpen, nu virker mit lydkort
Med tiden kommer jeg vel lidt mere ind i linux junglen da jeg godt kan lide systemet
Det er jo en fornøjelse man kan frigøre sig mere og mere fra windows
endnu engang tak for hjælpen også til jer andre der ligger en hjælpende hånd i forum
mvh Hans