Wireless opsætning på Fujitsu Siemens Li1718

[Maruks]

Hej derude.

Jeg er lidt ny med Ubuntu. Grunden til at jeg ikke slipper windows helt endnu er at jeg ikke kan komme på trådløst net med min bærbare. Den er af typen: Fujitsu Siemens Li1718 (http://www.fujitsu-siemens.co.uk/home/p ... _1718.html).

For at aktivere netkortet skal man fysisk trykke på en speciel netværksknap. Problemet er bare at denne knap ikke virker i Ubuntu. Jeg har prøvet utallige guides og howto's, men har omsider fundet denne som ser troværdi ud: http://ubuntuforums.org/archive/index.php/t-644899.html

Somsagt er jeg lidt ny i brug af terminal osv, og jeg har lidt problemer med at udføre guiden.

Guiden er som følger:

Kode: Vælg alt

On with the HOWTO:

1. Make sure your system is up to date, and includes the necessary tools to compile the new kernel modules:
sudo apt-get update
sudo apt-get upgrade
sudo apt-get install build-essential

2. Get the patched source:
wget http://www.cakey.de/acerhk/archives/acerhk-0.5.35.tgz
wget http://snapshots.madwifi.org/special/madwifi-ng-r2756+ar5007.tar.gz

3. Build the new Madwifi modules, to enable support for the Atheros AR5007EG card:
tar xfvz madwifi-ng-r2756+ar5007.tar.gz
cd madwifi-ng-r2756+ar5007
make
sudo make install


4. Build the new acerhk module, needed to enable the wireless button on the machine:
cd ..
tar xfvz acerhk-0.5.35.tgz
cd acerhk-0.5.35
make
sudo make install

5. Create a file containing instructions which the system will carry out when the acerhk module is loaded - see comments in the file:
sudo gedit /etc/modprobe.d/amilo_special_keys.modprobe
and paste the following into the file, save and exit
# set up kernel module acerhk to enable Fujitsu Siemens Amilo Li1718 special keys
# and enable wireless when the module is inserted.
# NOTE: to have the wireless hardware disabled until you press the wireless key on the laptop,
# simply replace "echo 1" with "echo 0" in the command below.

install acerhk /sbin/modprobe --ignore-install acerhk force_series=6805 autowlan=1; echo 1 > /proc/driver/acerhk/wirelessled

6. Remove the acerhk module which is shipped with Ubuntu:
sudo rm /lib/modules/2.6.22-14-generic/ubuntu/misc/acerhk.ko

7. Rebuild the module dependencies database
sudo depmod -a

8. Tell the system to load the acerhk module at boot time - it won't otherwise, as it's not actually an Acer laptop!
sudo gedit /etc/modules
add on a new line at the end of this file, then save and exit:
acerhk

9. restart your machine and you should have a working wifi card.

Når jeg når til step 3, får jeg denne fejl når jeg skriver "make" i terminalen:

Kode: Vælg alt

markus@markus-laptop:~$ cd madwifi-ng-r2756+ar5007
markus@markus-laptop:~/madwifi-ng-r2756+ar5007$ make
make: *** No targets specified and no makefile found.  Stop.
markus@markus-laptop:~/madwifi-ng-r2756+ar5007$ sudo make install
make: *** No rule to make target `install'.  Stop.

Kan godt være jeg er komplet idiot men kunne godt bruge lidt hjælp.

På forhånd tak.

[Casper Hansen]

Tror du skal have build-essential installeret.

Kode: Vælg alt

sudo apt-get install build-essential

[Maruks]

Tror du skal have build-essential installeret.

Kode: Vælg alt

sudo apt-get install build-essential

Når jeg kører denne får jeg følgende:
build-essential er i forvejen den nyeste version.

[andsen]

Guiden er som følger:
[code]On with the HOWTO:

1. Make sure your system is up to date, and includes the necessary tools to compile the new kernel modules:
sudo apt-get update
sudo apt-get upgrade
sudo apt-get install build-essential

2. Get the patched source:
wget http://www.cakey.de/acerhk/archives/acerhk-0.5.35.tgz
wget http://snapshots.madwifi.org/special/ma ... 007.tar.gz

Hej Maruks
Jeg har selv en masse bøvl med mit trådløse netværk, der kun kan virke med Madwifi-driveren. Det jeg har markeret med fed foroven er den driver der skal installeres, men den driver guiden her refererer er forældet og indeholder ikke andet end en tekstfil, der siger at man skal gå ind på http://www.madwifi.org og hente madwifi-0.9.4.tar.gz og så ellers følge den samme guide.
Det har jeg selv gjort utallige gange, men har ikke haft held med at få det til at virke endnu.
Men prøv at hente madwifi-0.9.4.tar.gz, gå guiden igennem og se om du kan få det til at fungere

[Jeg]

Ellers har jeg lige smidt et eksemplar af madwifi-ng-2756+ar5007 op her: http://ifile.it/lnohead

[Maruks]

Kan slet ikke få det til at virke. Havde håbet på at opdateringen gjorde underværker men negativ.

[PKO]

Hej,

kan du smide resultatet af denne kommando i terminalen

Kode: Vælg alt

dmesg

efter en opstart af din komputer.

[Maruks]

SÅ FIK JEG DET SKU TIL AT VIRKE!!!


LØSNING:
http://blog.hyperandy.com/2008/11/01/at ... mment-2959

Der var et par småfejl i guiden men det lykkedes alligevel

Har rettet fejlene og dette burde virke hvis andre har samme problem:

Kode: Vælg alt

Atheros AR242x Ubuntu 8.10 Ibex

In Ubuntu it really does try to detect your Atheros chip. In Ubuntu 7.10 the wireless on my laptop was detected as the AR5006EG and I use ndiswrapper and the net5416.inf driver. On Ubuntu 8.04 my wireless was detected as the AR242x and I was able to download ndisgtk (in the repos) and use the net5211.net driver, (the ndisgtk is just a graphical interface for ndiswrapper, very easy and very nice!). This time (Ubuntu 8.10) it wasn’t detected as the AR5006EG, it was however detected as the AR242x BUT I couldn’t use ndisgtk as before. I’m thinking it’s because they updated the network manager in 8.10. Either way here is how I got it working.

Remember TAB is your friend in the terminal!

To check what you wireless is detected as just run the following in the Terminal:

lspci | grep Wireless

These steps are done using Ethernet, if it is unavailable, just go to any computer with Internet and download the mad wifi snapshot shown in these steps. Just follow the step from there once you have gotten the file.

1) First disable Ubuntu’s Atheros HAL driver if loaded:

Click ‘System’ –> ‘Administration’–> ‘Hardware drivers’ then deactivate support for the Atheros 802.11 wireless driver

I rebooted just to make sure there was no chance it was running.

Everything else is done in the Terminal :)

2) Get the Ubuntu built essentials package, this will allow the program to compile:

sudo apt-get install build-essential

**if this is a new install of 8.10 you MUST do “sudo apt-get update” (without quotes) to update your repositories

3) Download the madwifi snapshot:

wget http://snapshots.madwifi.org/madwifi-hal-0.10.5.6/madwifi-hal-0.10.5.6-r3861-20080903.tar.gz

4) Untar (unzip) the newly downloaded file:

tar xvf madwifi-hal-0.10.5.6-r3861-20080903.tar.gz

5) Go into the newly created directory:

cd madwifi-hal-0.10.5.6-r3861-20080903

6) Then compile the package:

make

7) The install the package:

sudo make install

8) Then load the newly created module:

sudo modprobe ath_pci

if yours is like mine you may not get a wifi light, in that case you won’t know if the card is on, just try pushing the button to toggle it (on the Acer 4720Z it’s a picture of a satillite)

9)  If your wireless is working after this when you reboot the computer it won’t to fix it, you must add it to the kernel boot modules list:

In the terminal type “sudo gedit /etc/modules”(without quotes) and add “ath_pci”(again without quotes) to the bottom of the list if you don’t have anything in the list just add it to the bottom. Click ‘Save’ and that’s it.

FYI: If there is ONLY one reason you want to update to Ubuntu 8.10, it’s for the boot-up time. It’s supa-speedy.

Knæk og bræk