ubuntu 14.04 64bit
Jeg kan ikke få crossover cable ethernet file sharing til at virke mellem en debian 8 og ubuntu 14.04 computer til at virke.
Derfor har jeg prøvet diverse ting. Dette resulterede i en error message vedr. /etc/samba/samba.config filen. Denne slettede jeg med gksudo nautilus. Derefter virkede det slet ikke. Med synaptic package manager complete removal af system-config-samba. I synaptic er der nu 17 software installerede pakker, hvis jeg søger på 'samba'. Hvordan foretager jeg complete removal af alt samba, for derefter at installere igen? Jeg bemærkede, at 'local network share' bruger system-config-samba. Fordi hvis complete removal af den pakke, kan man ikke lave en 'local network share' af en folder. Tak.
slette alt samba og geninstallere
-
- Admin
- Indlæg: 5566
- Tilmeldt: 26. apr 2010, 02:40
- IRC nickname: ClaudiuS
- Geografisk sted: Nyborg [fyn]
Re: slette alt samba og geninstallere
For at fjerne både server og client:
For at installere igen:
Kilde: http://askubuntu.com/questions/74838/how-do-i-completely-remove-samba
Kode: Vælg alt
sudo apt-get remove --purge samba smbclient libsmbclient
For at installere igen:
Kode: Vælg alt
sudo apt-get install samba smbclient libsmbclient
Kilde: http://askubuntu.com/questions/74838/how-do-i-completely-remove-samba
Med Venlig Hilsen
Klaus
Kører Ubuntu 22.04 på ASUS All-Series, og Probook 4520s.
Gratis Ubuntumagasin: http://fullcirclemagazine.org/
https://mega.nz/folder/aJsmCYKa#dxMHKTi4Idmz6hiVpsI68Q
Klaus
Kører Ubuntu 22.04 på ASUS All-Series, og Probook 4520s.
Gratis Ubuntumagasin: http://fullcirclemagazine.org/
https://mega.nz/folder/aJsmCYKa#dxMHKTi4Idmz6hiVpsI68Q
-
- Admin
- Indlæg: 20862
- Tilmeldt: 15. nov 2009, 15:04
- IRC nickname: AJenbo
- Geografisk sted: Vanløse, København
Re: slette alt samba og geninstallere
Prøv at dele dit problem lidt op, i samme paragraf starter du med ethernet kabler og afslutter med pakken håndtering i Synaptic (samt en blanding af engelsk og dansk).
1: Sæt dit netværk op. Tjek at det virker ved at pinge en maskine fra den anden.
2: Hvilken fejl får du? Har du oprettet en ny, og korrekt, konfiguration af samba?
3: hvis du vil afinstallere alle pakker der omhandler samba så purge alle pakker, og installer dem efterfølgende igen. Det kunne dog lyde som om det eneste du ønsker er at genkonfiguere dem.
1: Sæt dit netværk op. Tjek at det virker ved at pinge en maskine fra den anden.
2: Hvilken fejl får du? Har du oprettet en ny, og korrekt, konfiguration af samba?
3: hvis du vil afinstallere alle pakker der omhandler samba så purge alle pakker, og installer dem efterfølgende igen. Det kunne dog lyde som om det eneste du ønsker er at genkonfiguere dem.
Re: slette alt samba og geninstallere
Tak for svar.
Skrev command line
Genstartede computeren.
Skrev command line
Genstartede computeren.
Det ændredede ikke fejlmeldingen.
Forbindelsen med ethernet lan cable mellem computerne virker sandsynligvis. Når cable tilsluttes meddeler både ubuntu og debian, at der er en wired connection. Fordi jeg ikke kunne få folder sharing til at virke, fordi der fremkom en access denied message, begyndte jeg at nano editere en config file. Da det gav fejlmeldinger, deletede jeg config filen. Hvilket sandsynligvis er grunden til, at når jeg click 'browser network' fremkommer icons for den anden computer ikke i nautilus. Når jeg click 'browser network' og 'windows network' på debian, fremkommer følgende fejlmelding= unable to access location Failed to retrieve share list from server. No such file or directory. Når jeg vil 'local network share' en folder på ubuntu, fremkommer en fejlmelding.
Jeg vil have samba default filer igen, så ubuntu ses i debian 'network browser'.
Skrev command line
Kode: Vælg alt
sudo apt-get remove --purge samba smbclient libsmbclient
Genstartede computeren.
Skrev command line
Kode: Vælg alt
sudo apt-get install samba smbclient libsmbclient
Genstartede computeren.
Det ændredede ikke fejlmeldingen.
Forbindelsen med ethernet lan cable mellem computerne virker sandsynligvis. Når cable tilsluttes meddeler både ubuntu og debian, at der er en wired connection. Fordi jeg ikke kunne få folder sharing til at virke, fordi der fremkom en access denied message, begyndte jeg at nano editere en config file. Da det gav fejlmeldinger, deletede jeg config filen. Hvilket sandsynligvis er grunden til, at når jeg click 'browser network' fremkommer icons for den anden computer ikke i nautilus. Når jeg click 'browser network' og 'windows network' på debian, fremkommer følgende fejlmelding= unable to access location Failed to retrieve share list from server. No such file or directory. Når jeg vil 'local network share' en folder på ubuntu, fremkommer en fejlmelding.
Jeg vil have samba default filer igen, så ubuntu ses i debian 'network browser'.
- Vedhæftede filer
-
- folder.png (45.74 KiB) Vist 651 gange
-
- Admin
- Indlæg: 20862
- Tilmeldt: 15. nov 2009, 15:04
- IRC nickname: AJenbo
- Geografisk sted: Vanløse, København
Re: slette alt samba og geninstallere
Genskab den fil du slettede
-
- Admin
- Indlæg: 20862
- Tilmeldt: 15. nov 2009, 15:04
- IRC nickname: AJenbo
- Geografisk sted: Vanløse, København
Re: slette alt samba og geninstallere
Eks en anden computer, eller et backup, find et eksempel på nettet.
-
- Indlæg: 2667
- Tilmeldt: 21. nov 2006, 10:06
- Geografisk sted: Fredericia
Re: slette alt samba og geninstallere
hvordan ser din/etc/samba/smb.conf ud?
og prøv med nedestende for at slette al samba konfiguration.
og prøv med nedestende for at slette al samba konfiguration.
Kode: Vælg alt
sudo apt purge samba samba-common
Forfatter til Ubuntuguiden: http://www.vidas.dk/guides/ubuntuguiden.html
Kører LTS udgaverne.
"It's always easy if you know how to do it."
Kører LTS udgaverne.
"It's always easy if you know how to do it."
-
- Admin
- Indlæg: 20862
- Tilmeldt: 15. nov 2009, 15:04
- IRC nickname: AJenbo
- Geografisk sted: Vanløse, København
Re: slette alt samba og geninstallere
Tak for svar. Det viste sig, at der ikke var nogen samba folder eller config file i etc.
Jeg testede
Derefter var samba fjernet i synaptic package manager. Når man første gang foretager 'share local network' højreklikker man den folder, man vil dele. Derefter fremkommer et vindue og man installerer software. Genstarter computeren. Derefter højreklikker man igen folderen og vælger 'share local network'. Derefter er folderen markeret med 2 pile.
Efter ovenstående command, højreklikkede jeg folderen. Option 'share local network' vises ikke. I synaptic package manager var samba ikke installeret. Det gjorde jeg. Men man kan ikke vælge 'share local network', når man højreklikker en folder. Dvs 'share local network' er ikke tilbage på samme måde.
Efter ovenstående command og installering af samba med synaptic package manager, kom der igen en samba folder i etc. Med en smb.conf.
Dvs højreklik folder, vælg 'share local network' virker ikke. Forslag?
Jeg testede
Kode: Vælg alt
sudo apt purge samba samba-common
Derefter var samba fjernet i synaptic package manager. Når man første gang foretager 'share local network' højreklikker man den folder, man vil dele. Derefter fremkommer et vindue og man installerer software. Genstarter computeren. Derefter højreklikker man igen folderen og vælger 'share local network'. Derefter er folderen markeret med 2 pile.
Efter ovenstående command, højreklikkede jeg folderen. Option 'share local network' vises ikke. I synaptic package manager var samba ikke installeret. Det gjorde jeg. Men man kan ikke vælge 'share local network', når man højreklikker en folder. Dvs 'share local network' er ikke tilbage på samme måde.
Efter ovenstående command og installering af samba med synaptic package manager, kom der igen en samba folder i etc. Med en smb.conf.
Kode: Vælg alt
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
# - When such options are commented with ";", the proposed setting
# differs from the default Samba behaviour
# - When commented with "#", the proposed setting is the default
# behaviour of Samba but the option is considered important
# enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.
#======================= Global Settings =======================
[global]
## Browsing/Identification ###
# Change this to the workgroup/NT-domain name your Samba server will part of
workgroup = WORKGROUP
# server string is the equivalent of the NT Description field
server string = %h server (Samba, Ubuntu)
# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
# wins support = no
# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
; wins server = w.x.y.z
# This will prevent nmbd to search for NetBIOS names through DNS.
dns proxy = no
#### Networking ####
# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
; interfaces = 127.0.0.0/8 eth0
# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself. However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
; bind interfaces only = yes
#### Debugging/Accounting ####
# This tells Samba to use a separate log file for each machine
# that connects
log file = /var/log/samba/log.%m
# Cap the size of the individual log files (in KiB).
max log size = 1000
# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
# syslog only = no
# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
syslog = 0
# Do something sensible when Samba crashes: mail the admin a backtrace
panic action = /usr/share/samba/panic-action %d
####### Authentication #######
# Server role. Defines in which mode Samba will operate. Possible
# values are "standalone server", "member server", "classic primary
# domain controller", "classic backup domain controller", "active
# directory domain controller".
#
# Most people will want "standalone sever" or "member server".
# Running as "active directory domain controller" will require first
# running "samba-tool domain provision" to wipe databases and create a
# new domain.
server role = standalone server
# If you are using encrypted passwords, Samba will need to know what
# password database type you are using.
passdb backend = tdbsam
obey pam restrictions = yes
# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
unix password sync = yes
# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
passwd program = /usr/bin/passwd %u
passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .
# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
pam password change = yes
# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
map to guest = bad user
########## Domains ###########
#
# The following settings only takes effect if 'server role = primary
# classic domain controller', 'server role = backup domain controller'
# or 'domain logons' is set
#
# It specifies the location of the user's
# profile directory from the client point of view) The following
# required a [profiles] share to be setup on the samba server (see
# below)
; logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
# logon path = \\%N\%U\profile
# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
; logon drive = H:
# logon home = \\%N\%U
# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
; logon script = logon.cmd
# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe. The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u
# This allows machine accounts to be created on the domain controller via the
# SAMR RPC pipe.
# The following assumes a "machines" group exists on the system
; add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u
# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe.
; add group script = /usr/sbin/addgroup --force-badname %g
############ Misc ############
# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
; include = /home/samba/etc/smb.conf.%m
# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
; idmap uid = 10000-20000
; idmap gid = 10000-20000
; template shell = /bin/bash
# Setup usershare options to enable non-root users to share folders
# with the net usershare command.
# Maximum number of usershare. 0 (default) means that usershare is disabled.
; usershare max shares = 100
# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
usershare allow guests = yes
#======================= Share Definitions =======================
# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each
# user's home directory as \\server\username
;[homes]
; comment = Home Directories
; browseable = no
# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
; read only = yes
# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
; create mask = 0700
# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
; directory mask = 0700
# By default, \\server\username shares can be connected to by anyone
# with access to the samba server.
# Un-comment the following parameter to make sure that only "username"
# can connect to \\server\username
# This might need tweaking when using external authentication schemes
; valid users = %S
# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
; comment = Network Logon Service
; path = /home/samba/netlogon
; guest ok = yes
; read only = yes
# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
; comment = Users profiles
; path = /home/samba/profiles
; guest ok = no
; browseable = no
; create mask = 0600
; directory mask = 0700
[printers]
comment = All Printers
browseable = no
path = /var/spool/samba
printable = yes
guest ok = no
read only = yes
create mask = 0700
# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
comment = Printer Drivers
path = /var/lib/samba/printers
browseable = yes
read only = yes
guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
; write list = root, @lpadmin
Dvs højreklik folder, vælg 'share local network' virker ikke. Forslag?
-
- Indlæg: 2667
- Tilmeldt: 21. nov 2006, 10:06
- Geografisk sted: Fredericia
Re: slette alt samba og geninstallere
Problemet er at det er to vidt forskellige ting.
Det du har installeret er sambaserveren, som kræver at du konfigurerer den igennem /etc/samba/smb.conf. Du kan følge min guide her: http://www.vidas.dk/guides/fildeling.html.
Den funktion du søger virker så vidt jeg ved kun for filer i din hjemmemappe, og funktionaliteten er begrænset.
Det du har installeret er sambaserveren, som kræver at du konfigurerer den igennem /etc/samba/smb.conf. Du kan følge min guide her: http://www.vidas.dk/guides/fildeling.html.
Den funktion du søger virker så vidt jeg ved kun for filer i din hjemmemappe, og funktionaliteten er begrænset.
Forfatter til Ubuntuguiden: http://www.vidas.dk/guides/ubuntuguiden.html
Kører LTS udgaverne.
"It's always easy if you know how to do it."
Kører LTS udgaverne.
"It's always easy if you know how to do it."